Hi all,
I dont know if this is allowed here, if not than were els can i go?
My YUPITERU MVT - 7100 lost all his freqs when he hit something a few months ago.
Now i would start with putting them al back again, he dont react as i push the buttons.
It doesnt make any sence if he's on Battery or 220V power, he remains death !!!!!
The only thing on the screen is FM - 20 khz and 143.860.
I can change the freq with the right button on top & change volume with the other,
But thats all !!!!!
Can anyone from you help me with this item please
Greetings Frits
Problem with scanner
Moderator: joost
Forum rules
![]() |
- ETURSPOTTER
- Scramble Junior
- Posts: 159
- Joined: 31 Dec 2007, 18:48
- Type of spotter: Mil. Aviation.
- Location: Swalmen
- Contact:
- Rabbit
- Scramble Addict
- Posts: 1224
- Joined: 24 Oct 2007, 09:16
- Subscriber Scramble: Hensie
- Location: Utrecht
Re: Problem with scanner
Factory reset?
To perform the reset
1. Make sure the radio is powered on
2. Use a small object to press and hold the micro switch located beneath the small opening on the side
panel
3. The radio will reset and then go to VFO mode
http://www.radiomanual.info/schemi/RX/Y ... _N2MCA.pdf
To perform the reset
1. Make sure the radio is powered on
2. Use a small object to press and hold the micro switch located beneath the small opening on the side
panel
3. The radio will reset and then go to VFO mode
http://www.radiomanual.info/schemi/RX/Y ... _N2MCA.pdf
Cheers,
Jeroen
Jeroen
- ETURSPOTTER
- Scramble Junior
- Posts: 159
- Joined: 31 Dec 2007, 18:48
- Type of spotter: Mil. Aviation.
- Location: Swalmen
- Contact:
Re: Problem with scanner
Hi Rabbit,
Doesnt work !!!
But i havent got a Mircro switch on the leftside beneath the reset switch.
During pressing on the reset switch the display gone blank.
Doesnt work !!!
But i havent got a Mircro switch on the leftside beneath the reset switch.
During pressing on the reset switch the display gone blank.
- FISHER01
- Scramble Master
- Posts: 3315
- Joined: 13 May 2004, 21:33
- Type of spotter: DIE HARD
- Subscriber Scramble: Yups
- Location: Enschede, 5 miles south south east of EHTW
- Contact:
Re: Problem with scanner
Did you checked the "lock" switch? must be downwards
and other way is to reset. put a small pointy object in the little hole (under the lock switch, above the letters reset)
the fact it went all clear, could indicate your internal memory battery is empty, will be a good idea to replace it. or all clear could happen more often and sometimes when you switch batteries it will clear to.
If this not work, could be you have a lose connection, you can try to put some little pressure on the display and soundbox
Jos
and other way is to reset. put a small pointy object in the little hole (under the lock switch, above the letters reset)
the fact it went all clear, could indicate your internal memory battery is empty, will be a good idea to replace it. or all clear could happen more often and sometimes when you switch batteries it will clear to.
If this not work, could be you have a lose connection, you can try to put some little pressure on the display and soundbox
Jos
greetzz. Jos FISHER01 K.™
![Image](http://farm8.staticflickr.com/7065/6996376731_c8e4abb157_m.jpg)
![Image](http://farm8.staticflickr.com/7065/6996376731_c8e4abb157_m.jpg)
- ETURSPOTTER
- Scramble Junior
- Posts: 159
- Joined: 31 Dec 2007, 18:48
- Type of spotter: Mil. Aviation.
- Location: Swalmen
- Contact:
Re: Problem with scanner
Hi Jos,
I think the only thing left is to switch the internal memory battery.
Is this something i can do self or not.
Took a long time this awnser, but comes due to my work as a trucker.
My holliday starts now so now i got the time for it.
T.IA. Frits
I think the only thing left is to switch the internal memory battery.
Is this something i can do self or not.
Took a long time this awnser, but comes due to my work as a trucker.
My holliday starts now so now i got the time for it.
T.IA. Frits